Andy's 91' 80q

[rennenmsports]

3880B17E-C611-4865-8002-9658234DAFDF.jpeg (65.38 KiB) Viewed 47748 times

Urs front hub with an E36 wheel bearing. Had to take about 3mm off the knuckle in a cone shaped angle. it’s definitely a really tight fit

[rennenmsports]

A6612661-0261-4428-B434-5D0ED4EB53C0.jpeg (106.21 KiB) Viewed 47729 times

Bruce lee’s 1 inch punch to spread the transmission tunnel for the 01E 6 spd

[rennenmsports]

B0D75535-5CB9-4EBA-9DF5-628798B9B987.jpeg (131.06 KiB) Viewed 47726 times

It’s getting really close. Just need a front brake set up. If anyone has one for sale please pm me

[rennenmsports]

CF9C3DED-512F-4777-A2C2-B562E0C85109.jpeg (69.07 KiB) Viewed 47580 times

I used a counter sink bit to be able to use a flat headed taper bolt so I can install a -10an banjo fitting for the transmission cooler

[rennenmsports]

18FB8EC4-FCC2-4933-9C03-8579D24904E2.jpeg (159.74 KiB) Viewed 44717 times

Rebuilt prop shaft center support
Bearing from McMaster carr 4668k295 works

[rennenmsports]

-10 lines for the transmission cooler

70682280128__A94618B9-0B8E-41DB-B75A-29EE7C948027.jpeg (104.79 KiB) Viewed 42356 times

70682279011__70E6D2CA-F54F-420E-B965-1336A19FA256.jpeg (106.8 KiB) Viewed 42356 times

[DE80q]

Does it move on its own power yet?

[rennenmsports]

Does it move on its own power yet?

Almost waiting on a T fitting to finish the engine oil cooler lines. I was bleeding the brakes when the master decided to go out. Glad it did at home. It is original. Also rear sway bar end links and a DIY alignment so I can get it to an alignment rack. But that doesn’t keep it from moving on its own. The last thing is to tune the VEMS. I’m all the way down in south Florida so I’m hoping Marc can help remote tune it at some point. No idea what that entails.

[rennenmsports]

I figured out a simple way to strengthen the push rod on the clutch master. I just stacked up nuts and grinded one down to meet the necessary adjustment

70507743513__763B045D-23F9-4275-89B9-EE3973082101.jpeg (116.93 KiB) Viewed 42302 times

[rennenmsports]

She’s ready to tune

[rennenmsports]

IMG_5161.jpeg (107.11 KiB) Viewed 41574 times

[rennenmsports]

It started misfiring pretty bad. It has Amazon coils. So I ordered Okada coils for the ttrs in hopes that it stops the issue. I also previously relayed the coils with a 50A/30A relay. It was getting pretty warm so I ordered a 70A replacement. When everything gets here we’ll see if the problem goes away and we can finish tuning it. I got the hood on. Had to drill holes in it for the exhaust. Fortunately I have a new one in Delaware.

[rennenmsports]

72014647413__3BF4DD15-126C-4A2A-B03B-3600360E62D6.jpeg (117.42 KiB) Viewed 34863 times

To be continued

[rennenmsports]

The new coils solved the issue only it lost a lot of compression due to piston ring failure. I finally am able to start removal and disassembly of the entire engine this time.

[rennenmsports]

She’s all back together again. So I called Marc for a remote tune. Over the internet and through the computer it started right up. Thank you!!

[Marc]

She’s all back together again. So I called Marc for a remote tune. Over the internet and through the computer it started right up. Thank you!!

any time. its what we do.

[rennenmsports]

After starting it for the first time the second time around. Had a loose oil cooler hose and a leaky freeze plug. They are now fixed. Gotta get a plate and registration and I should also hook up the electric power steering pump. Not sure if that affects tuning. It is more of a load on the engine. I’m going to idle it more to make sure it’s ready as much as I can.

[rennenmsports]

Everything is great 100 or so miles later. I needed a vacation from it. It turned into an obsession again and now I can relax. It’s back to it now.
First is the power steering doesn’t work. I used a mini cooper electric pump that’s not coming on.
Just ordered one today. This weekend I’ll finally be able to really drive it

[DE80q]

I'll believe it when I see it!

I shouldn't say though, mine hasn't moved in 2 years haha.

[rennenmsports]

I'll believe it when I see it!

I shouldn't say though, mine hasn't moved in 2 years haha.

Haha. It’s been a 18 year long project. It’s hard to believe myself. So long my mind still doesn’t register that it’s available to use

[rennenmsports]

Hello again. It’s been a long time. I decided to keep it. Too sentimental. The piston rings went. I’m going to be able to get a short block from Marc in about 6 months. Now that I know which turbine housing I’m going to use I can make the exhaust and intake as well.

[rennenmsports]

IMG_0077.jpeg (3.39 MiB) Viewed 154 times

I pushed her back into the garage on the first. Happy new year everyone. for the third time around. This time I’m getting a short block professionally built. Didn’t have much luck the first two times. I’ve gotta make the intake and exhaust first so we can tune it properly. The intake tubing was easy. The down pipe on the other hand won’t be. I’m using 2 1/2” schedule 10 304ss pipe.

IMG_0077.jpeg (3.39 MiB) Viewed 154 times

[rennenmsports]

IMG_0093.jpeg (3.69 MiB) Viewed 7 times