86 Alpine white 4000 commemorative , AAN / 01E / VEMS

[Afterthought]

Ahh.. looked like a new crank pulley on that!

The shop did a good job of washing everything up for me ...
I didn't think much about the crank pulley when I sent it it to have it balanced so I am committed to going AAN accessory belt now . But I have the parts and it makes for a really sweet setup.
Right now I have V-belts in it, and that works fine as well.


Sent from my iPhone using Tapatalk

[Afterthought]

You have a project thread on here Driggs?


Sent from my iPhone using Tapatalk

[Afterthought]

Got something in the works for my EFR, gonna have to re-flange my manifold and add a V-band for a wastegate to it. Stealing the manifold I was going to use in the URQ .
Also going to see if I can shorten it up just a hair and gain a little space between the turbo and wheel well.






Sent from my iPhone using Tapatalk

[the german]

Please tell me you have been out hooning in all the snow Bham has been getting

[Afterthought]

Please tell me you have been out hooning in all the snow Bham has been getting

I actually just flew in from Vegas last night so I got out last night and today , good 6" or more at my place and at 4 am I always get the first tracks


Sent from my iPhone using Tapatalk

[Afterthought]

Please tell me you have been out hooning in all the snow Bham has been getting

I actually just flew in from Vegas last night so I got out last night and today , good 6" or more at my place and at 4 am I always get the first tracks


Sent from my iPhone using Tapatalk

[Driggs]

You have a project thread on here Driggs?


Sent from my iPhone using Tapatalk

No.. I started one for my 91 200 but havent done anything to car in a while

I keep the urq project on a dedicated page on my website. Then if everyone switches boards, I dont have to worry about it.

http://b2resource.com/driggs83urq.php

[Afterthought]

Got my manifold set up for my EFR 7163 and TiAL wastegate (still need a wastegate)








I am considering, once I get the downpipe made, maybe getting the downpipe, turbo exhaust housing, and manifold coated in Cerakote or similar. Not sure the cost but it would look cool

[quattrobros]

What kind of intake manifold is that? Haven't seen that one before.

[Afterthought]

What kind of intake manifold is that? Haven't seen that one before.

It's from BST turbo.
I got a deal on it locally from someone who had already imported it.
http://www.bst-turbo.de


Sent from my iPhone using Tapatalk

[85oceanic]

Getting the engine together . Got the Piston rings on, Rods in , Pistons and rods in the block. Everything is toqued down and the engine rotates nice by hand .



Got my INA breather on... cool looking piece and will simplify things. I like

What is this .... Breather? Where did you pick it up?

[Afterthought]

Getting the engine together . Got the Piston rings on, Rods in , Pistons and rods in the block. Everything is toqued down and the engine rotates nice by hand .



Got my INA breather on... cool looking piece and will simplify things. I like

What is this .... Breather? Where did you pick it up?

Issam makes them . His company is INA or his handle I think is Wizard-of-OD on most forums , don't think I have ever seen him on the project pad though. I'm sure Marc could get it for you...
If you've ever tried to remove the stock breather from the block, it inevitably gets damaged . The one issam makes you can unbolt it and open it up, it has some packing in it of some sort . Coalescer or Mist eliminator type material in it .
Most of all it looks cool !


Sent from my iPhone using Tapatalk

[85oceanic]

Issam makes them . His company is INA or his handle I think is Wizard-of-OD on most forums , don't think I have ever seen him on the project pad though. I'm sure Marc could get it for you...
If you've ever tried to remove the stock breather from the block, it inevitably gets damaged . The one issam makes you can unbolt it and open it up, it has some packing in it of some sort . Coalescer or Mist eliminator type material in it .
Most of all it looks cool !


Sent from my iPhone using Tapatalk

What's the hose adapter for it look like?

[Afterthought]

Issam makes them . His company is INA or his handle I think is Wizard-of-OD on most forums , don't think I have ever seen him on the project pad though. I'm sure Marc could get it for you...
If you've ever tried to remove the stock breather from the block, it inevitably gets damaged . The one issam makes you can unbolt it and open it up, it has some packing in it of some sort . Coalescer or Mist eliminator type material in it .
Most of all it looks cool !


Sent from my iPhone using Tapatalk

What's the hose adapter for it look like?

I used an -12 , I think he can out whatever size you need in there




Sent from my iPhone using Tapatalk