Small Chassis Rear Dif Center Bushing Mount -- Pre-order

[AngryTaco]

I will have the pre-order price sometime Monday or Tuesday after my poly manufacturer gets back to me with quote information. I made a few prototypes for customers (including Greene on here) and they are very nice.

As you will see in the pictures, I designed these to be used with the factory inner sleeve. I did this in order to retain wall thickness and maintain the overall integrity of the housing (think cracked housings due to 03junk)

Removal of the factory rubber crap is relatively easy with a torch. Just be sure to do it outside. Be sure to clean the sleeve well and remove all the old rubber. DO NOT MELT OR REMOVE THE INNER SLEEVE

This is the end all be all problem solver for your clunking rear dif!!!

Retail Price: $65

Pre-order price: $55 + free shipping

Looking for 10-12 orders total to help offset the mold costs.













Signed Up:

Steve B (FB-P - S) -- 1x
JD L (FB-P - S) -- 1x
Scubagli (P) --1x
Tom R (FB-P - S) -- 1x
Jim Greene (P - S) -- 1x
Jetstream (P) -- 1x
Dana (P - S) -- 1x
Dan W (T) --1x
Namreg (P -shipped 1 owed 1) -- 2
Peters (P - S) -- 2x
FFF (P - S) --1x
MDriggs (FB - P - S) -- 2x

--------------------

Total (P): 15x

[Peters]

Jared, don't you mean the outer sleeve that is presses into the housing? the inner sleeve would go around the mounting bolt through the middle of the bushing

[AngryTaco]

Jared, don't you mean the outer sleeve that is presses into the housing? the inner sleeve would go around the mounting bolt through the middle of the bushing

Correct. When I say inner sleeve, I'm referencing to the housing only with no bushing installed. With the bushing installed, it would be considered the outer sleeve. Either way, dont remove it lol

[ringbearer]

Why did you choose to leave it in?

[AngryTaco]

edit

[AngryTaco]

As you will see in the pictures, I designed these to be used with the factory inner sleeve. I did this in order to retain wall thickness and maintain the overall integrity of the housing (think cracked housings due to 03junk)

[ringbearer]

Ah, gots it now.

[AngryTaco]

Supplier got back to me.

Retail price is $60 + shipping.

Pre-order Price is $55 + free shipping.

Going to pull trigger on mold in a week or so.

[AngryTaco]

Pulling the trigger on this on Monday everyone.

[dana]

i'd be down for one of these for $55. paypal is motormaniac2@aol.com if you want to send me an invoice.

[AngryTaco]

Invoice sent!

[dana]

paid, thanks.

[scubagli]

Paid.

[dana]

when might these be shipping?

[AngryTaco]

The mold is still currently being made, so good possibility end of the month.

[AngryTaco]

mold is just about done so everyone should start seeing their parts in 2-3 weeks!

[audifreakjim]

Fuck. I better finish my car

[AngryTaco]

Wait so if I dont get these to Jim in time for BBQ and I show up with a 20v....does that mean my 20v is faster than a built 07k?

[PRY4SNO]

Why are you allowed to post 20v again?

We had a good thing going...

[Peters]

so if I need to order a pair now, retail price?

[AngryTaco]

I'll still give you the pre-order price. Anything helps that will offset the inital mold costs

[AngryTaco]

Why are you allowed to post 20v again?

We had a good thing going...

Because only YOU guys see 20v. I see 20v

[dalspaugh]

I didn't realize there were was a thread for this, you know I'm in!

[AngryTaco]

The first prototypes arrived today. Placing the bulk order tomorrow and getting everyone's!!!!!!!!

[FFF]

Is it too late to get in on the order? fbatwork@gmail.com for invoice if I am not