Rubi PTE6062 Build - 615WHP 510WTQ

[mushasho]

uploadfromtaptalk1370893300542.jpg (57.52 KiB) Viewed 35692 times

Sent from my HTC One using Tapatalk 2

[EDIGREG]

Take a wider photo so we can see the top of the cam sprockets and the chain.

If you count 7 teeth up on each cam from the marks (teeth with marks being #1), there should be 10 links between those two teeth.

[EDIGREG]

picture is worth 1000 words

[mushasho]

Awesome!!! Didn't wanna search for that with dirty fingers on my phone, I know I had seen this before and a conversation regarding the possibility of having to time 7a's a but differently in an AAN application... I think it was a thread started by Dave in QW. I haven't seen mention of it since so im assuming it was more of a theoretical post...

Oh, and has anyone been able to spec out the wider washers needed for the ARP head studs... Trying to find those locally if someone has the measurements. Sort of wanna get that far today...

Thanks
Sent from my HTC One using Tapatalk 2

[mushasho]

Spot on?

uploadfromtaptalk1370905231473.jpg (62.57 KiB) Viewed 35667 times

Sent from my HTC One using Tapatalk 2

[Mcstiff]

7a & 7a it is... Assembling now..
how many open links should there be an on chain now?



Sent from my HTC One using Tapatalk 2

Hold on, how are you setting the cam sync? I don't think, may be wrong, that it is as simple as 180* off.

[mushasho]

7a & 7a it is... Assembling now..
how many open links should there be an on chain now?

Sent from my HTC One using Tapatalk 2

Hold on, how are you setting the cam sync? I don't think, may be wrong, that it is as simple as 180* off.

I believe I have it like soo

picture is worth 1000 words

[Mcstiff]

Right, that is the stock alignment.

I am saying, is this as simple as phasing the exhaust +-180* to make into a, properly performing, intake?

[mushasho]

Oh I think you're under the assumption that I mix and match my cams... I went 7A Intake and 7A Exhaust in there intended location.... none of that "AAN Exhaust Cam as the intake & 7A Exhaust" stuff... Ain't got time for that right now... lol

[Mcstiff]

Yes, this post was misleading:

How about AAN exhaust cam on the intake side paired with 7a exhaust side?

uploadfromtaptalk1370886518936.jpg

Sent from my HTC One using Tapatalk 2

:carryon:

[mushasho]

Then these guys quickly responded:

That will work just fine, but the most gains are with both 7A intake/exhaust

Use 7a exhaust on both Some machining/degreeing required.

Hank

Since I don't have 2 sets of 7A's, I really couldn't go with Hanks suggestion... Since I DO have AAN Exhaust cams, I might modify that one at a later date and use it as on the intake...

[mushasho]

A little dress up...



Sent from my HTC One using Tapatalk 2

[Hank]

7a intakes don't have enough duration to support power above 6800 on bigger turbos. By putting the exhaust in the intake slot, you can grab a bit more lift and a tad more duration. With the cost of 7a cams, it is coming close to what proper Cats or other cams are designed to do, with far better specs. Still, there are some really good dyno plots where the power does not drop off at 7000 like I am accustom to seeing on straight 7a cams. This is also why retarding the cams with a cam gear yields great results..

[Mcstiff]

7a intakes don't have enough duration to support power above 6800 on bigger turbos. By putting the exhaust in the intake slot, you can grab a bit more lift and a tad more duration. With the cost of 7a cams, it is coming close to what proper Cats or other cams are designed to do, with far better specs. Still, there are some really good dyno plots where the power does not drop off at 7000 like I am accustom to seeing on straight 7a cams. This is also why retarding the cams with a cam gear yields great results..

Hopefully the costs keep increasing, good for the 07K fund

[mushasho]

uploadfromtaptalk1370987106508.jpg (75.37 KiB) Viewed 35616 times

uploadfromtaptalk1370987194792.jpg (72.13 KiB) Viewed 35616 times

uploadfromtaptalk1370987243318.jpg (77.8 KiB) Viewed 35616 times

Sent from my HTC One using Tapatalk 2

[85oceanic]

Looking really sharp man?

7a intakes don't have enough duration to support power above 6800 on bigger turbos. By putting the exhaust in the intake slot, you can grab a bit more lift and a tad more duration. With the cost of 7a cams, it is coming close to what proper Cats or other cams are designed to do, with far better specs. Still, there are some really good dyno plots where the power does not drop off at 7000 like I am accustom to seeing on straight 7a cams. This is also why retarding the cams with a cam gear yields great results..

How does retarding the cams yield more power? Is it because the valves are opening "late" after TD help? Reason I ask is because as you know Hank, I'm going to be on 7a cams. If having an adjustable cam gear will help me achieve a better power band, I better start thinking about picking one up.

[da_trem]

Retarded cam timing as been discussed here:

http://www.motorgeek.com/viewtopic.php? ... ng#p235352

[85oceanic]

Thanks man and holy frick, over a 50whp gain buy just adjusting the cam timing. That's crazy.

[mushasho]

Looking really sharp man?

Thanks!

Sent from my KFTT using Tapatalk HD

[themagellan]

Built to the hilt
Dress to impress

[mushasho]

uploadfromtaptalk1371174498989.jpg (107.79 KiB) Viewed 35575 times

uploadfromtaptalk1371174523143.jpg (103.56 KiB) Viewed 35575 times

uploadfromtaptalk1371174546802.jpg (113.73 KiB) Viewed 35575 times

uploadfromtaptalk1371174562079.jpg (100.49 KiB) Viewed 35575 times

Sent from my HTC One using Tapatalk 2

[chaloux]

Is it done yet? What's the hold up? Driving impressions? Why don't you put a 07k in instead?

/dickmode

[mushasho]

Is it done yet? What's the hold up? Driving impressions? Why don't you put a 07k in instead?

/dickmode

Lol....
1) Done? Not done but getting there
2) Hold Up? Still waiting on parts ordered/paid over a month ago
3) Impressions? I think it'll be expensive at the pump once it's done (thinking of upgrading the fueling after break in)
4) 07k? I have one, but it's not going anywhere near here...

/earlymorningrushresponsemode

Sent from my HTC One using Tapatalk 2

[mushasho]

Quick rinse out of hibernation..

uploadfromtaptalk1371258427317.jpg (99.75 KiB) Viewed 35543 times

Placed behind shop...

uploadfromtaptalk1371258838705.jpg (111.72 KiB) Viewed 35543 times

Commence break down...

uploadfromtaptalk1371259064692.jpg (92.12 KiB) Viewed 35543 times

Sent from my HTC One using Tapatalk 2

[mushasho]

uploadfromtaptalk1371487142691.jpg (118.43 KiB) Viewed 35518 times

uploadfromtaptalk1371487153263.jpg (123.38 KiB) Viewed 35518 times

Sent from my HTC One using Tapatalk 2