Derracudas zermatt 20vt,6spd, 351awhp - July 4th drive vid

quattro87 · Post by **quattro87** » Mon Jul 13, 2009 9:42 am

Noooooo!! Sounds like a bit of deja vu happening here. Ask Hank if that sounds familiar to him.

Derek, you probably ought to just put that car on a trailer and run it up to Las Vegas to junk it. In fact if you want to just run it by my house I'll take care of the rest. :wink: :wink:

Sorry to hear!

Post by **Hank** » Mon Jul 13, 2009 9:55 am

Yeah, I had that happen once as well. The standoffs for the timing belt cover dropped down there, and that spells a certain death for the timing belt. Hopefully it did it slow enough that only two valves bent before it came to a stop..

WAUG0806 · Post by **WAUG0806** » Mon Jul 13, 2009 9:56 am

:curses:

Ouch... did it cut the TB or make it jump timing?

derracuda · Post by **derracuda** » Mon Jul 13, 2009 9:56 am

send me your address John, i'll be right over

with an empty trailer to steal your URQ mwuhahahaa

WAUG0806 · Post by **WAUG0806** » Mon Jul 13, 2009 9:57 am

derracuda wrote:send me your address John, i'll be right over with an empty trailer to steal your URQ mwuhahahaa

derracuda · Post by **derracuda** » Mon Jul 13, 2009 10:00 am

just made it jump. the belt is still intact, no apparent damage, but it's not staying on the car for $10 it costs to replace it.

death 4kqt · Post by **death 4kqt** » Mon Jul 13, 2009 10:01 am

valves OK??? that would be nice!

derracuda · Post by **derracuda** » Mon Jul 13, 2009 10:06 am

1-4 0psi
#5 has 115psi :roll:

Post by **Hank** » Mon Jul 13, 2009 10:18 am

that sucks. The day after buzz kill is the worse. You just sulk around unmotivated. I had that day about a month ago. It sucked

Hybrid_Hatch · Post by **Hybrid_Hatch** » Mon Jul 13, 2009 10:21 am

ShavedQuattro wrote:that sucks. The day after buzz kill is the worse. You just sulk around unmotivated. I had that day about a month ago. It sucked

Wait, when did you stop sulking?

death 4kqt · Post by **death 4kqt** » Mon Jul 13, 2009 10:22 am

oh man, really sorry to hear that derek

Post by **Hank** » Mon Jul 13, 2009 10:23 am

Hybrid_Hatch wrote:
ShavedQuattro wrote:that sucks. The day after buzz kill is the worse. You just sulk around unmotivated. I had that day about a month ago. It sucked

Wait, when did you stop sulking?

True, I avoid that part of the shop right now, as I just stare for at least 30 minutes if I do....

derracuda · Post by **derracuda** » Mon Jul 13, 2009 10:29 am

i'm not sulking. i have a time crunch... i'm on the horn now to get everything lined up to get her back together. i want to show and race the car at the pacific waterland show again this year in sept.

i have a header to build
downpipe to build
intake manifold to build
intercooler to finish
AAN harness to wire up
interior to install
flywheel, trans, clutch master, slave, and line to install

and now the engine to repair...

i think if i concentrate, i can do it. i think that's all i need to do...

Post by **Hank** » Mon Jul 13, 2009 10:33 am

that is quite the list there Derek!!!

death 4kqt · Post by **death 4kqt** » Mon Jul 13, 2009 10:36 am

thats quite the list, but judging from your past project success, I think its totally do-able.

derracuda · Post by **derracuda** » Mon Jul 13, 2009 10:41 am

well, in the modified words of smokey the bear, you can help retroactively prevent dereks broken car by visiting the swapmeet section and perusing a long list of various goods that need a new home

derracuda · Post by **derracuda** » Mon Jul 13, 2009 10:52 am

the offending jerk...

my2000apb · Post by **my2000apb** » Mon Jul 13, 2009 10:55 am

oh shit noooooooooooo omg derek

yes you have a long list but from the past 50!!!! pages before this, ive seen nothing short beautified insanity, truly amazing work.

so a small head rebuild on some valves and you should be ready to go, ah well and all the other stuff listed, but think east task should be way easier than all the 5k dash parts right? yea

my2000apb · Post by **my2000apb** » Mon Jul 13, 2009 11:03 am

derracuda wrote:well, in the modified words of smokey the bear, you can help retroactively prevent dereks broken car by visiting the swapmeet section and perusing a long list of various goods that need a new home

derracuda wrote:

how much for a d-cuda custom exhaust

:jawdrop: :jawdrop: :jawdrop: :drool:

:heart:

Post by **HT Motorsport** » Mon Jul 13, 2009 11:24 am

Its just disgusting how clean the underside of that car is! Damned New England winters!

quattro87 · Post by **quattro87** » Mon Jul 13, 2009 1:07 pm

derracuda wrote:i'm not sulking. i have a time crunch... i'm on the horn now to get everything lined up to get her back together. i want to show and race the car at the pacific waterland show again this year in sept.

i have a header to build
downpipe to build
intake manifold to build
intercooler to finish
AAN harness to wire up
interior to install
flywheel, trans, clutch master, slave, and line to install

and now the engine to repair...

i think if i concentrate, i can do it. i think that's all i need to do...

Have you ran these plans by the soon to be wife yet? I've noticed that as of late you don't spend near as much time on MG as you used to. I was thinking I might even have half a chance at some of the swap meet stuff now, but looking at that list you might just not have time for MG anymore.

a_CQ · Post by **a_CQ** » Mon Jul 13, 2009 1:55 pm

:( Sorry to hear this....stupid little mishaps that make for expensive repairs are never good.
Good luck with that list..

derracuda · Post by **derracuda** » Tue Jul 14, 2009 10:10 pm

well.. if photobucket would cooperate, i could put up some intercooler update pics.

no dice tonight... photobucket maintainence jerks

i think i need one of these stickers under my hood now..

my2000apb · Post by **my2000apb** » Tue Jul 14, 2009 10:59 pm

what is that piece of metal, the spacer that slides on the stud for the timing belt cover?

derracuda · Post by **derracuda** » Wed Jul 15, 2009 8:09 am

that piece of metal..... it's part of the sheetmetal from behind the bumper, under the SS beauty trim.

anyhow, enough of that, i wanna think about the IC otherwise i'll get sidetracked and drop the ball on my big fab projects here. the repairs are straight forward, this custom stuff takes concentration and creative thinking, which is what i need to produce from my mind

intercooler mounting... i had some carriage bolts left over from the old A8 parts car and i thought, huh, this would make mounting and unmounting the IC easy. only need to hold one tool to undo it. i drilled the holes and stuck the bolts through...

then sucked them through..

then pulled it apart and carefully filed the holes square so that the bolts aren't a super tight fit, but they won't rotate now when you tighten the nut from the backside.

end tanks!

before we go on, i did a little googling of end tank design, and came across this, which i found interesting

it's an F1 car piece. super thin tanks, but blended out nicely. i need the clearance of a low tank, so i'm going to make a slight compromise to get the fitment i need, although my tanks look to be considerably larger than these.

I cut out the end plates and then formed them a bit on a block of wood so they fit better. my welding skills are sometimes better... sometimes not. still learning.

i have a box of misc pipes to rummage through and the ones i'll be using here are volvo bits.

note to self, and everyone else welding aluminum who doesn't do it for a living... FIT EVERYTHING PERFECTLY

it's a pain in the neck to weld up gaps if you aren't super proficient with the welder.

this is the general idea for the inlet

i cut the elbow out to give it a nice inlet angle and point it in the right direction on the car

i'm fitting 2" pipe to a 3" round endcap, so i had to open up and form it a little. turns out 82mm bearing shells work great for this!

then set it all in place and mark the main tank

carefully cut it out

and how it should hopefully all turn out