'84 Audi Coupe Gt grp2

Document and share your build!

'84 Audi Coupe Gt grp2

Postby Afterthought » Fri Jun 11, 2021 6:11 am

Man that looks great . So difficult welding all those in the car . Props for taking that on.

A common thing to run into is when you are closing up the last bit of the hole on a tube that’s welded on both sides , there are no more gaps for the remaining gases to escape ( besides the one you are welding) so the escaping gas blows away your shield gas. Similar to if you were back purging and didn’t have a vent hole .
What people do usually in this case is preemptively drill a hole with a diameter of 1/8” or so which would be covered by the tube being welded over it, so that the tubes are all vented together - if that makes any sense .
But as you mentioned it could be any number of things . Inside not being clean , lack of shield gas , or possibly too much purge could draw in oxygen . If using tig I don’t know what type of size of cup you use but I like to use one that has the diffuser in it , that way you can turn shield gas way up if needed but without a ton of turbulence or velocity .
Afterthought
 
Posts: 1244
Joined: Jan 16, 2014
Location: Bellingham, Wa

Re: '84 Audi Coupe Gt grp2

Postby mrdeye » Fri Jun 11, 2021 10:51 am

Thank you and thanks for sharing your knowledge. The whole cage will be mig welded with .035 wire, 75/25 mix and the nozzle on the end of the gun is a 1/2 opening. I thought of putting a vacuum at a joint/opening away from the joint I was welding to pull any gas away, but also thought that might creat another problem and like you said thing start to seal up. I like the 1/8 hole Idea. What if the hole was drilled a little farther away from the joint so that as the joint is completely filled there is still a place for gas to escape and then fill hole and smooth out? It’s only an 1/8 hole, but what kind of effect would it have on the cages structural integrity with 1/8 holes in multiple places? Everything effects everything. One thing at time. I’ll lay some welds down and see what happens with having the regulator at right setting.

Thanks for your time and input!
✌️
Mr.
Daily driver: '01 Toyota 4Runner
Project car: '84 Audi Coupe GT
Previous cars:
'95 S6 Avant, '87 5K TQ, '95 VW Golf, '84 VW Jetta turbo diesel, '84 VW GTI
mrdeye
 
Posts: 159
Joined: Nov 13, 2016
Location: Colorado

Re: '84 Audi Coupe Gt grp2

Postby PRY4SNO » Sun Jun 20, 2021 9:48 pm

You can always seal the 1/8" vent holes later, that's no bother. The filler metal will of course be stronger than the base metal.

The bit about cleaning is huge... prep is 80% of the job when welding, unless you screw up or miss something. Then it's 100%.

I'll try to run your issues by a couple of the welders at work before I go home for days off and see if any of them can lend some experience/insight (though I think the boys here have it surrounded as well as getting your regulator dialed as the major points).

Otherwise not a lot to add, aside from the project is really progressing nicely.
Find me on Instagram @pry4sno

|| 2010 Golf Sportwagen TDI /// #farmenwagen
|| 2002 Dodge Ram 2500 24vt 4x4 #bertancummins
|| 1992 80 quattro 20v /// Eventual AAN'd Winter Sled
|| 1990 Coupe quattro /// Because Racecar
User avatar
PRY4SNO
 
Posts: 2428
Joined: Mar 3, 2013
Location: Edmonton, AB

Re: '84 Audi Coupe Gt grp2

Postby mrdeye » Wed Jun 23, 2021 11:41 pm

Thanks for that! Been practicing and I’m gonna have to say it was operator error. Welds look like ass, but their’s no porosity or undercut.
“Everybody’s got a plan until you get punched in the face!”
Mike Tyson
✌️
Mr.
Daily driver: '01 Toyota 4Runner
Project car: '84 Audi Coupe GT
Previous cars:
'95 S6 Avant, '87 5K TQ, '95 VW Golf, '84 VW Jetta turbo diesel, '84 VW GTI
mrdeye
 
Posts: 159
Joined: Nov 13, 2016
Location: Colorado

Re: '84 Audi Coupe Gt grp2

Postby PRY4SNO » Thu Jun 24, 2021 2:45 pm

As an inspector said to me at work one day, "ugly isn't a discontinuity." Keep at it and one day you'll turn that hamburger into neatly stacked dimes!
Find me on Instagram @pry4sno

|| 2010 Golf Sportwagen TDI /// #farmenwagen
|| 2002 Dodge Ram 2500 24vt 4x4 #bertancummins
|| 1992 80 quattro 20v /// Eventual AAN'd Winter Sled
|| 1990 Coupe quattro /// Because Racecar
User avatar
PRY4SNO
 
Posts: 2428
Joined: Mar 3, 2013
Location: Edmonton, AB

Re: '84 Audi Coupe Gt grp2

Postby mrdeye » Sun Sep 26, 2021 12:27 am

Ok, so yeah, I got discouraged. Thought my tube welding practice would pay off. Not so much, ehh. But I’m gonna keep on keep’n on because I’ve seen worse. Yup, you won’t be seeing any close up shots of my welds. Today I got the fire wall tubes welded on to the front down tubes, did some rust prevention in areas that will be hard to get to when finished. Bought a porta-power that’s not good or better but the BEST to push things back into place. I cleaned up all porosity issues, welded everything on top of the cage completely, so no need to drop the cage down but holding off on welding the main hoop base plates just in case. And those holes in the dash are speed holes that need to be closed up. :bangshead: A few pics for your viewing discomfort. Thanks for looking.✌️
Attachments
4B48FF6B-DA68-40F6-9BCE-FBFCC83469AE.jpeg
4B48FF6B-DA68-40F6-9BCE-FBFCC83469AE.jpeg (479.25 KiB) Viewed 5572 times
8713886E-8B21-4556-8A52-9124AF166FE1.jpeg
8713886E-8B21-4556-8A52-9124AF166FE1.jpeg (350.12 KiB) Viewed 5572 times
BCDF6E6C-48CE-4C7A-84C0-74486B6740DD.jpeg
BCDF6E6C-48CE-4C7A-84C0-74486B6740DD.jpeg (361.83 KiB) Viewed 5572 times
C4858883-5177-4D22-A26E-8E310EBD1849.jpeg
C4858883-5177-4D22-A26E-8E310EBD1849.jpeg (391.76 KiB) Viewed 5572 times
Mr.
Daily driver: '01 Toyota 4Runner
Project car: '84 Audi Coupe GT
Previous cars:
'95 S6 Avant, '87 5K TQ, '95 VW Golf, '84 VW Jetta turbo diesel, '84 VW GTI
mrdeye
 
Posts: 159
Joined: Nov 13, 2016
Location: Colorado

Re: '84 Audi Coupe Gt grp2

Postby mrdeye » Sat Oct 30, 2021 9:04 am

Added some gusseting to the knee bar. The cage warped a little, it teeter totters on the drives side A pillar and passenger side main hoop tubes. Depending on which way I manipulated the cage the opposite corners would be high. I decided to put a good tack weld at the passenger side A pillar tube and utilize the OE seat belt attaching point and ratchet strap that corner of the cage down. Worked out great! The door sill tubes are tacked in place, I’ll will pre-fit the door tubes in place to make sure everything is going to fit where it should. Thanks for looking. :beer:
Attachments
F59D8490-DB95-458A-99C8-087D2971C285.jpeg
F59D8490-DB95-458A-99C8-087D2971C285.jpeg (399.51 KiB) Viewed 3890 times
FE8A79CE-A02C-4FB2-92E2-A389269D6E57.jpeg
FE8A79CE-A02C-4FB2-92E2-A389269D6E57.jpeg (358.71 KiB) Viewed 3890 times
8BDB89A1-1E81-4824-BB46-36A71998F169.jpeg
8BDB89A1-1E81-4824-BB46-36A71998F169.jpeg (505.42 KiB) Viewed 3890 times
880E933C-C0EF-4BF3-B2D3-472235CD8500.jpeg
880E933C-C0EF-4BF3-B2D3-472235CD8500.jpeg (324.43 KiB) Viewed 3890 times
45DC427D-5946-4F98-9C28-607A6DE7ACBC.jpeg
45DC427D-5946-4F98-9C28-607A6DE7ACBC.jpeg (325.4 KiB) Viewed 3890 times
Mr.
Daily driver: '01 Toyota 4Runner
Project car: '84 Audi Coupe GT
Previous cars:
'95 S6 Avant, '87 5K TQ, '95 VW Golf, '84 VW Jetta turbo diesel, '84 VW GTI
mrdeye
 
Posts: 159
Joined: Nov 13, 2016
Location: Colorado

Re: '84 Audi Coupe Gt grp2

Postby mrdeye » Fri May 27, 2022 7:57 pm

They gave it to me….
Attachments
E09ECE2B-00F3-4E36-97F9-ADA0BE2ABAE6.jpeg
E09ECE2B-00F3-4E36-97F9-ADA0BE2ABAE6.jpeg (542.73 KiB) Viewed 988 times
Mr.
Daily driver: '01 Toyota 4Runner
Project car: '84 Audi Coupe GT
Previous cars:
'95 S6 Avant, '87 5K TQ, '95 VW Golf, '84 VW Jetta turbo diesel, '84 VW GTI
mrdeye
 
Posts: 159
Joined: Nov 13, 2016
Location: Colorado

Re: '84 Audi Coupe Gt grp2

Postby mrdeye » Sun May 29, 2022 12:47 am

BOOM!!! I want to thank the seller and his son for their patience while I figured out what I needed to make them work. New lug nuts and hub centric rings 73.00-57.10 Maxxim “Winner” by Konig,
15”x6.5, weigh 16.5 pounds and are all straight.
Thanks for looking! ✌️
Attachments
F7E15A9B-C167-4256-828C-174251DD7CE0.jpeg
F7E15A9B-C167-4256-828C-174251DD7CE0.jpeg (388.27 KiB) Viewed 954 times
Mr.
Daily driver: '01 Toyota 4Runner
Project car: '84 Audi Coupe GT
Previous cars:
'95 S6 Avant, '87 5K TQ, '95 VW Golf, '84 VW Jetta turbo diesel, '84 VW GTI
mrdeye
 
Posts: 159
Joined: Nov 13, 2016
Location: Colorado

Re: '84 Audi Coupe Gt grp2

Postby FFF » Tue May 31, 2022 4:25 am

Coming along nicely!


Sent from my iPhone using Tapatalk Pro
FFF
 
Posts: 321
Joined: Nov 1, 2014

Re: '84 Audi Coupe Gt grp2

Postby mrdeye » Tue May 31, 2022 1:04 pm

At a sloths pace but thanks!!
:beer:
Mr.
Daily driver: '01 Toyota 4Runner
Project car: '84 Audi Coupe GT
Previous cars:
'95 S6 Avant, '87 5K TQ, '95 VW Golf, '84 VW Jetta turbo diesel, '84 VW GTI
mrdeye
 
Posts: 159
Joined: Nov 13, 2016
Location: Colorado

Previous

Return to Projects

Who is online

Users browsing this forum: Majestic-12 [Bot] and 29 guests

cron